Bling Bling!
Rub on Foil
Available in 16 Colors!!

New! Blue Rainbow (pictured below)

Abalone Pearl - a pearl background with swirls of light purple and green (this one shows best on darker papers and is a favorite with
polymer clay artists)

Gold

Silver

Copper

Red

Purple

Green

Rainbow Swirl - a silver background with
green and purple swirls

Primary Rainbow

Gold Hologram* - looks gold but reflects a rainbow of colors as light hits it

Chunky Gold*

Silver Hologram* - looks silver but reflects
a rainbow of colors

Silver Fire* - silver with a moire pattern that
reflects a rainbow of colors

Is It Green? - or gold, or blue, or purple?

Blue

(*) Indicates a Holographic Foil - see below for tips

***Warning*** Rub on foils are EXTREMELY addictive!***
Fast, easy, and shiny! No other technique can compare.
Use with Sticky Powder, glue pen, double stick tape, Stamp and Stick glue pad, or any dry adhesive. Rub on foils give a bright, shiny, metallic finish to your project.

Works with Quickie Glue Pen!! Click here for pictured step-by-step instructions

Also works great with tapes. Click here to see samples with tapes and tiny no hole glass beads

See bottom of page for techniques and tips!

To use with Sticky Powder:

1. Stamp your design with any embossable ink. You may use an embossing pad, VersaMark or any wet pigment pad. See below for some extra tips on using Sticky Powder.

2. Sprinkle Sticky Powder onto the stamped design and pour excess Sticky Powder back into the container.

3. Tap off any excess and wipe off stray powder before heating.

4. Use an embossing gun or heat tool to melt the Sticky Powder. It is very important not to overheat the Sticky Powder. You want to melt the powder just until it turns shiny and then remove heat. If you overheat the Sticky Powder, it will "dry out" and not be sticky.

5. Once powder is melted, it should be sticky and ready to apply the Bling Bling Rub on Foil. Place the foil sheet on the sticky image - COLOR OR SHINY SIDE UP!! -and rub FIRMLY or press with your finger. When rubbing, make sure to press the foil on the entire image.

6. On the HOLOGRAPHIC foils - it is harder to get a "clean pull" when pulling off the foil. If you are having problems - here is a soloution: After step 5 above (rubbing) - heat for about 2 seconds with your heat gun (NOT TOO CLOSE) and then rub again. Let it cool for a few seconds before next.

7. Remove the foil sheet QUICKLY and foil should have now transferred to the Sticky Powder. If there are still areas on the image that are missing foil, replace the foil sheet, making sure that there is still foil in the area you are trying to get color; press again and remove.

To use Foiling Glue:

1. Apply Foiling Glue and let dry 1-3 hours so that you can press on the clue and it not smear. You can even wait overnight and the glue will be completely dry and clear - it will still be tacky. If using holographic foil - follow the steps above.

Also works with tapes!

Extra tips!
On the HOLOGRAPHIC foils indicated above (*) - it is harder to get a "clean pull" when pulling off the foil. If you are having problems - here is a soloution: After step 5 above (rubbing) - heat for about 2 seconds with your heat gun (NOT TOO CLOSE) and then rub again. Let it cool for a few seconds.

Remove the foil sheet and foil should have now transferred to the Sticky Powder. If there are still areas on the image that are missing foil, replace the foil sheet, making sure that there is still foil in the area you are trying to get color; press again and remove.

One suggestion on using STICKY POWDER - use a colored pigment ink - especially when using a white or light paper. This will make it easier to see the Sticky Powder change when you heat it and you will be less likely to overheat it. If you over heat the Sticky Powder - it WILL NOT be sticky!! Heat until it just turns shiny!

The foil sheet can be used until all the color is gone from the mylar backing.

Be sure to watch our site for online demos, samples and any new techniques.

back to supplies page